file:///svnroot/FUN3D

r71245

Update release notes about orphans
by nielsen at Thu Jul 31 11:27:24 EDT 2014

r71244

Omit orphan target points from near-field sonic boom cost function
by nielsen at Thu Jul 31 11:23:53 EDT 2014

r71243

To use a precise description, FEM surrogate surface, not FEM surface
by biedron at Thu Jul 31 07:05:00 EDT 2014

r71242

To correct a label
by biedron at Thu Jul 31 06:52:13 EDT 2014

r71241

To rearrange some bullets
by biedron at Thu Jul 31 06:44:21 EDT 2014

r71240

To fix a few minor things
by biedron at Wed Jul 30 22:22:53 EDT 2014

r71239

Try to clear up some discussion
by nielsen at Wed Jul 30 17:51:56 EDT 2014

r71238

Try to clear up some discussion
by nielsen at Wed Jul 30 17:51:34 EDT 2014

r71237

--Comment out some noisy diagnostics, 'figure out how to consolidate the "error" count to just the master node...
by jrc at Wed Jul 30 16:54:38 EDT 2014

r71236

--Interestingly enough, the logic to attempt to keep reverse flow from occurring at a subsonic outflow boundary backfires for this configuration.  These results are more correct than the previous goldens, as the code was switching to the wrong bc.  So this should fix the mpi failure due to -r71228 and -r71229.
by jrc at Wed Jul 30 16:52:45 EDT 2014

r71233

To tie http://abi3.larc.nasa.gov/projects/PHYSICS_MODULES/changeset/3017 to FUN3D.
by kleb at Wed Jul 30 11:48:02 EDT 2014

r71232

To allow only processors with data on the boundary communicate with the external CHAR code.
by mazaheri at Wed Jul 30 11:45:00 EDT 2014

r71229

--Some code clean-up to fix unit, remove unused variables
by jrc at Wed Jul 30 06:45:11 EDT 2014

r71228

--Allow for sinusoidal variation of the total pressure and total temperature at the subsonic inflow boundary
--Couched the equations inside a test for code_id to try to shield the adjoint until that part is worked out.
--Also placed before pt ramping, which is a different critter from the sinusoidal concept...and incompatible besides.
--Cleaned out the test for supersonic flow at the inflow boundary is it didn't appear to work in reality and was cluttering up the routine...seemingly...
by jrc at Wed Jul 30 06:04:19 EDT 2014

r71224

To use the more general check 
by biedron at Tue Jul 29 13:39:27 EDT 2014

r71223

To add some insanity checks for time dep. adjoint design, and to write out some input checks only from the master node
by biedron at Tue Jul 29 13:26:19 EDT 2014

r71222

To move toward multiple atributes for mesh motion and motion drivers (e.g. "rigid+deforming" and not just "rigid" or "deforming" with lots of if-then-buts logic when combinations are needed). By and large this is just a replacement of fortran "if trim(string) == 'test_string' then" to a function call that looks to see if 'test_string' is a subset of string.
by biedron at Tue Jul 29 11:22:35 EDT 2014

r71221

To commit some input changes prior to code commit
by biedron at Tue Jul 29 11:16:11 EDT 2014

r71219

--Framework for sinusoidal variation of (pt,tt) subsonic inflow boundary, add namelist parameters
by jrc at Tue Jul 29 06:24:18 EDT 2014

r71214

To move a couple of slides to backup position
by biedron at Mon Jul 28 12:34:28 EDT 2014

r71213

To add the force comparison chart
by biedron at Sun Jul 27 21:45:14 EDT 2014

r71212

To add an option for specifying how frequently trim updates are done
by biedron at Sun Jul 27 20:06:52 EDT 2014

r71210

To add some changes to use 6dof and trim together. Left in a lot of !---rtb breadcrumbs to be removed at a later time
by biedron at Sat Jul 26 15:35:10 EDT 2014

r71209

Typo
by thomasj at Sat Jul 26 12:50:51 EDT 2014

r71208

Typo
by thomasj at Sat Jul 26 12:15:04 EDT 2014

r71207

To add provisions for variable adaptation, stretching with no adaptation, and implicit k lines for right corner
by thomasj at Sat Jul 26 12:02:00 EDT 2014

r71206

To make some changes from today's walk-through
by biedron at Fri Jul 25 18:15:32 EDT 2014

r71205

get old bob paper online
by nielsen at Fri Jul 25 18:00:33 EDT 2014

r71204

add an old paper bob pointed out
by nielsen at Fri Jul 25 17:55:34 EDT 2014

r71202

--Clean out some more hybrid wall function tests
by jrc at Fri Jul 25 16:57:44 EDT 2014

r71201

Change starboard/port to windward.
by lrausch at Fri Jul 25 15:47:32 EDT 2014

r71200

To make it really the latest
by biedron at Fri Jul 25 15:24:36 EDT 2014

r71199

To commit the latest
by biedron at Fri Jul 25 15:23:57 EDT 2014

r71198

To correct limiter freezing test in case ndim > 5 for generic gas path.
by gnoffo at Fri Jul 25 14:50:41 EDT 2014

r71197

--Make 2D cylinder problem...2D
--Clear out hybrid wall function case for now
by jrc at Fri Jul 25 14:41:30 EDT 2014

r71196

--Clean out the hybrid wall function tests for now
--Change the dlr-kw case to 2D and give the backward face the tangency bc
by jrc at Fri Jul 25 14:37:52 EDT 2014

r71195

To correct evaluation of Mach number in sampling output and to enable limiter freezing in the generic gas path.
by gnoffo at Fri Jul 25 13:35:20 EDT 2014

r71194

Added 70psf 0deg yaw rigid oml to end of presentation.
by lrausch at Fri Jul 25 12:30:57 EDT 2014

r71193

--Added two k-w omega bc options in the wall function routine
--Added DLR-KW model function call with unit test.
--Some code cleanup
by jrc at Fri Jul 25 09:53:34 EDT 2014

r71192

--File cleanup for the NACA-4412 turbulence runs
by jrc at Fri Jul 25 09:22:58 EDT 2014